HackerReposA FIELD GUIDE TO OPEN SOURCE
ProSponsor the shelf♧ 0
← Back to top all-time
Ralim
IronOS
C2017–2026
Ralim / IronOS

IronOS

Open Source Soldering Iron firmware

17Distinct people
22Mentions
1Explicit recommenders
8.4KGitHub stars
REPOSITORY AT A GLANCE

What to know before exploring

What it is

Open Source Soldering Iron firmware

GitHub

Where it is used

No documented product use was verified in the last source check.

What people are saying

Oh boy, nice idea, but this looks complicated and time consuming. I recommend to get some good equipment first: - solder fume extractor (see below) - extra thin high quality…

sandreas used a recommendation phrase. One indexed comment matches. This is a phrase match, not a verdict.

No classified warning is attached to this page. Read the discussions before treating silence as approval.

Also in these discussions

No other repository is repeatedly linked in the same discussions.

This week on Hacker News

Nov 9–Nov 16 UTC · Direct repository links and separately labeled related project stories. Indexed through 11/16/2026, 4:59:52 AM UTC.

No direct repository links were found in the indexed HN discussions over the past seven days. Older discussions are available below.

Mentions over time

HN mentions by year22 dated mentions

Observed mentions: 2017-07-25 21:15:49 UTC to 2026-09-03 15:37:00 UTC.

02462017-01-01 00:00:00 UTC to 2018-01-01 00:00:00 UTC (exclusive): 1 mentions; 0 submissions, 1 comments20172018-01-01 00:00:00 UTC to 2019-01-01 00:00:00 UTC (exclusive): 0 mentions; 0 submissions, 0 comments2019-01-01 00:00:00 UTC to 2020-01-01 00:00:00 UTC (exclusive): 0 mentions; 0 submissions, 0 comments2020-01-01 00:00:00 UTC to 2021-01-01 00:00:00 UTC (exclusive): 3 mentions; 0 submissions, 3 comments2021-01-01 00:00:00 UTC to 2022-01-01 00:00:00 UTC (exclusive): 1 mentions; 0 submissions, 1 comments20212022-01-01 00:00:00 UTC to 2023-01-01 00:00:00 UTC (exclusive): 3 mentions; 0 submissions, 3 comments2023-01-01 00:00:00 UTC to 2024-01-01 00:00:00 UTC (exclusive): 7 mentions; 1 submissions, 6 comments2024-01-01 00:00:00 UTC to 2025-01-01 00:00:00 UTC (exclusive): 4 mentions; 0 submissions, 4 comments2025-01-01 00:00:00 UTC to 2026-01-01 00:00:00 UTC (exclusive): 0 mentions; 0 submissions, 0 comments2026-01-01 00:00:00 UTC to 2027-01-01 00:00:00 UTC (exclusive): 3 mentions; 0 submissions, 3 comments. Incomplete calendar period.2026*

* An incomplete calendar period is marked with an outlined bar. Its count is not directly comparable with a full period.

Counts come from the repository’s dated source evidence. Index cutoff: 2026-11-02 08:16:59 UTC.

View mention counts and date ranges
UTC ranges include their start and exclude their end. Select a period to filter the source evidence.
PeriodStart (UTC)End (exclusive, UTC)MentionsSubmissionsComments
20172017-01-01 00:00:00 UTC2018-01-01 00:00:00 UTC101
20182018-01-01 00:00:00 UTC2019-01-01 00:00:00 UTC000
20192019-01-01 00:00:00 UTC2020-01-01 00:00:00 UTC000
20202020-01-01 00:00:00 UTC2021-01-01 00:00:00 UTC303
20212021-01-01 00:00:00 UTC2022-01-01 00:00:00 UTC101
20222022-01-01 00:00:00 UTC2023-01-01 00:00:00 UTC303
20232023-01-01 00:00:00 UTC2024-01-01 00:00:00 UTC716
20242024-01-01 00:00:00 UTC2025-01-01 00:00:00 UTC404
20252025-01-01 00:00:00 UTC2026-01-01 00:00:00 UTC000
2026 (partial)2026-01-01 00:00:00 UTC2027-01-01 00:00:00 UTC303

What Hacker News says

3 sources
While soldering is not that hard, different tasks require different tools. Most of them can be from very cheap to very expensive. As a beginner I'd recommend the following: A small USB-C soldering iron supported by IronOS[1], e.g. Pinecil vor TS100 A solid stand with brass wool A KU soldering tip (looks a bit like a knife) for good heat transfer, too small tips are not good Thin (<=0.5mm) solder wire No clean flux (not a pen) Isopropyl alcohol Solder fume extractor (DIY is OK, if you're building it right) is good for your health Solder mat (blue silicone) Multimeter (not too cheap, around 20 bucks) Self closing tweezers Normal tweezers A wirecutter (blue 5 bucks from ali express) Manual Desoldering pump (engineer ss03 or a clone for cheaper) Most important is cleaning (alcohol, then flux) and heat transfer (tin your tip, your pads or your
Read the rest
wire before putting things together to ensure good heat transfer). Cleanup nicely and tin your tip after soldering to prevent corrosion. Optional but helpful for more professional tasks: Hot air station Auto Desoldering pump (ZD-8965) Adjustable power supply (fnirsi usbc, 30 bucks) Oscilloscope (mini beginner with display Cost around 30 bucks) Capton tape Solid Copper wire 1: https://github.com/Ralim/IronOS
In Ask HN: Resources to get good at soldering?
Starting with soldering, I find these 200$+ recommendations (regardless of which tool) hard to justify. # Soldering iron I'd recommend the Pinecil V2 with IronOS. https://github.com/Ralim/IronOS # Solder fume extraction I've built a simple fume extraction with an old plastic case, a 120mm fan and a sheet of carbon filter attached to a 120mm dryer / air conditioning hose. Around 15$ and good enough for soldering from time to time. # "Microscope" I simply use a strong (10x) magnifier glass with a LED ring (around 15$ on Amazon). I can't tell you how often I also used this thing for other purposes. # Desoldering Pump Because I needed it (beginners won't) I bought a ZD-8965 for 100 bucks and I'm very happy with this thing. I have whole list of cheap beginner to intermediate equipment, that'll do until you solder (semi) professionally.
In I hate soldering

MAKE YOURSELF AT HOME

A few shortcuts

/
Search the collection
?
Open this guide
Esc
Close dialogs and navigation

Your saved repositories and interests stay in this browser.